SEARCH FINESCALE.COM

Enter keywords or a search phrase below:

The coolest modeling tool ever!

4904 views
30 replies
1 rating 2 rating 3 rating 4 rating 5 rating
  • Member since
    December 2002
  • From: Harrisburg, PA
The coolest modeling tool ever!
Posted by Lufbery on Friday, November 2, 2007 10:10 AM

Hi all,

Earlier this week I finally bought a Badger electronic paint stirer. It may not be the coolest modeling tool ever, but it's pretty darned close. :)

I was getting frustrated trying to stir my paints with a toothpic and then shake them. The paint stirer works much better, is less messy, and only cost $12.

Regards, 

-Drew

Build what you like; like what you build.

  • Member since
    February 2003
  • From: A Spartan in the Wolverine State
Posted by rjkplasticmod on Friday, November 2, 2007 10:24 AM

Sounds like a good deal Drew.  I use lengths of sprue as paint stirrers rather than discarding them.  Works well for me.

Regards,  Rick

RICK At My Age, I've Seen It All, Done It All, But I Don't Remember It All...
  • Member since
    June 2007
Posted by squeakie on Friday, November 2, 2007 12:12 PM
 rjkplasticmod wrote:

Sounds like a good deal Drew.  I use lengths of sprue as paint stirrers rather than discarding them.  Works well for me.

Regards,  Rick

the coffee stirers that McDonalds has by the handfulls!

gary

  • Member since
    January 2007
Posted by Gigatron on Friday, November 2, 2007 12:26 PM

Micromark carries a no-brand version  http://www.ares-server.com/Ares/Ares.asp?MerchantID=RET01229&Action=Catalog&Type=Product&ID=80975

Every once in a while, they go on sale for $4.  I picked one up a few months ago and love it.  Stir for 5 seconds and you are golden.

-Fred

 

  • Member since
    April 2003
  • From: Hayward, CA
Posted by MikeV on Friday, November 2, 2007 1:28 PM
I love the Badger paint stirrer too, it does an excellent job and is easy to clean.

Wisdom is the right use of knowledge. To know is not to be wise. Many men know a great deal, and are all the greater fools for it. There is no fool so great a fool as a knowing fool. But to know how to use knowledge is to have wisdom. " Charles Spurgeon
  • Member since
    May 2005
  • From: Left forever
Posted by Bgrigg on Friday, November 2, 2007 2:16 PM
 Gigatron wrote:

Micromark carries a no-brand version  http://www.ares-server.com/Ares/Ares.asp?MerchantID=RET01229&Action=Catalog&Type=Product&ID=80975

Every once in a while, they go on sale for $4.  I picked one up a few months ago and love it.  Stir for 5 seconds and you are golden.

-Fred

But only if you use gold paint! Propeller [8-]

So long folks!

  • Member since
    August 2007
Posted by ben1227 on Friday, November 2, 2007 4:13 PM
Laugh [(-D] Ditto what someone said about coffee stirrers. I'm too cheap to go buy a purpose-built paint stirrer when McDonalds is right down the street!
.:On the Bench:. Tamiya 1/72 M6A1-K
  • Member since
    August 2006
  • From: Neenah, WI
Posted by HawkeyeHobbies on Friday, November 2, 2007 7:00 PM
I chuck a craft stick into my cordless dremel. Crack open the power to minimum and mix away. Toss the stick when done. Tools that multi task rock!

Gerald "Hawkeye" Voigt

http://hawkeyes-squawkbox.com/

 

 

"Its not the workbench that makes the model, it is the modeler at the workbench."

Moderator
  • Member since
    April 2003
  • From: USA
Posted by Matthew Usher on Saturday, November 3, 2007 7:12 AM

The electric stirrer is great. I've used it to bring some really old paint back to life, like tinlets of Humbrol that have all the pigment stuck at the bottom.

For everyday stuff, I use wooden coffee stirrers. There's a restaurant supply store a couple of doors down from my favorite hobby shop, and I bought a box of a million of them for a couple of bucks. They're probably 3/16 x 6, and are strong enough to mix epoxy.

Matt @ FSM 

 

  • Member since
    January 2007
Posted by Gigatron on Saturday, November 3, 2007 7:14 AM
 Bgrigg wrote:
 Gigatron wrote:

Micromark carries a no-brand version  http://www.ares-server.com/Ares/Ares.asp?MerchantID=RET01229&Action=Catalog&Type=Product&ID=80975

Every once in a while, they go on sale for $4.  I picked one up a few months ago and love it.  Stir for 5 seconds and you are golden.

-Fred

But only if you use gold paint! Propeller [8-]

 

Bill, you need help Wink [;)] Laugh [(-D]

-Fred

 

  • Member since
    February 2003
Posted by Jim Barton on Saturday, November 3, 2007 10:32 PM
I like to use the long greeting card holders used by florists; the clear plastic kind that look like a fork. I get the longest ones; about 16 or 18 inches, something like that. Using a pair of garden shears, I cut them into several pieces in such a way that some of the new paint stirrers have little paddles on them that I save for when I need to stir a brand-new bottle or ones that's been sitting around for a long time. I cut off the tines and use those for mixing small amounts of custom color. It's a bit complicated, perhaps, but one trip to the florist shop half a mile away and a dollar bill or so gets me a dozen card holders that can be made into sixty or so paint stirrers.

"Whaddya mean 'Who's flying the plane?!' Nobody's flying the plane!"

  • Member since
    October 2005
  • From: Maryland
Posted by usmc1371 on Wednesday, November 7, 2007 2:40 PM

I use Tamiya's Paint Stirrers.  The little cup at the end comes in handy for transferring small amount of paint.

-Jesse

  • Member since
    February 2007
  • From: Casa Grande, Az.
Posted by DesertRat on Wednesday, November 14, 2007 12:07 AM
 rjkplasticmod wrote:

Sounds like a good deal Drew.  I use lengths of sprue as paint stirrers rather than discarding them.  Works well for me.

Regards,  Rick

As do i! (Isn't that why they give you all that sprue in a kit?)Propeller [8-]

Warmest regards,

Roger

  • Member since
    April 2003
  • From: Hayward, CA
Posted by MikeV on Wednesday, November 14, 2007 12:52 AM

Once you use an electric stirrer you will wonder what you have been missing all these years. Wink [;)]

Nothing stirs paint better or more thoroughly. 

Wisdom is the right use of knowledge. To know is not to be wise. Many men know a great deal, and are all the greater fools for it. There is no fool so great a fool as a knowing fool. But to know how to use knowledge is to have wisdom. " Charles Spurgeon
  • Member since
    May 2004
  • From: Dallas
Posted by KINGTHAD on Wednesday, November 14, 2007 9:31 AM

Sign - Ditto [#ditto]

Thad

  • Member since
    April 2004
  • From: UK
Posted by Jon_a_its on Thursday, November 15, 2007 5:06 AM
Picked up something similar in a UK 'Pound shop' (My 2 cents [2c]200c!)
  
It came with some mini-grinding sticks, but bent-up a long 3/32 brass rod into an eye, like a towing pintle

East Mids Model Club 32nd Annual Show 2nd April 2023

 http://www.eastmidsmodelclub.co.uk/

Don't feed the CM!

 

  • Member since
    December 2007
Posted by JViguers on Thursday, December 13, 2007 9:39 PM

McDonald's coffee stirrer....why didn't I think of that before?

On the workbench: Pegaso 90mm Templar Sergeant
  • Member since
    September 2005
Posted by TB6088 on Saturday, December 15, 2007 11:58 AM

I agree about the electric paint mixer.  I've had the "no name" brand from Micromark for a couple of years now ($10), it does a better, faster job of mixing than toothpicks, sprue, or any hand held variety of stick, and like previously mentioned, it is so efficient you can resurrect old paint that could never be brought back by hand stirring.  The other great advantage is that it wastes less paint, by far.  When you use sticks a relatively large amount of paint is left on the stick, which gets costly after a time if you use good quality paints and mix small amounts (which is common).  The more surface area on the stick, the more paint you lose (McDonald's coffee mixers vs toothpicks, for instance) With the electric mixer, when I finish mixing the paint, I raise it just slighly above the surface of the paint in the bottle and let the mixer run for a couple of seconds.  The centrifugal force of the spinning action removes most of the paint and it ends up back in the bottle.  Given the cost of a bottle of Tamiya or Gunze acrylic, which is what I use most often, my electric mixer has paid for itself a couple times over by now.  It's also nice to finish mixing paint in less than a minute, rather than five--- unless you get some perverse pleasure out of (literally) going through the motions.  

TomB

  • Member since
    January 2007
  • From: Southampton England
Posted by Viper Has The Lead on Saturday, December 15, 2007 12:12 PM
Hello there Lufbery,
                           I couldn't agree more, for a simple tool it's brilliant, a minute or two whizzing with it and even those nasty metallics that seperate while you look at them are sorted out. My other 'don't be without' tools are a couple of Tamiya stainless steel paint stirrers, great for keeping the paint mixed once the Badger has done it's job. 'Blu Tac' a million uses for this one. Liquid cement, once you get used to using it, nothing beats it.
Happy modelling
Mick C.
"All modern aircraft have four dimensions: span, length, height and politics. TSR.2 simply got the first three right." Sir Sydney Camm
  • Member since
    September 2003
Posted by mightymax on Tuesday, December 25, 2007 11:30 AM

I found one very similar at the Dollar Tree store for a buck. I think they were marketing it as a beverage stirrer. The tip was a tad big to fit inside a Model Master size jar but would fit comfortable inside Tamiya size bottles.  I modified it by cutting a piece out of the tip then crimping the circle on the end to a smaller diameter. The stirrer now fits inside MM size jars.

I could'nt pass it up at 1.00!

 

Max Bryantr

  • Member since
    February 2003
  • From: Lacombe, LA.
Posted by Big Jake on Monday, December 31, 2007 9:02 PM
I've had one for a few years now and have probally save the cost in paint easy. I also have the Robart paint shaker, that works great too.

 

 

  • Member since
    August 2006
  • From: The Great State of Wyoming
Posted by wyoroy on Monday, December 31, 2007 10:14 PM

The motor on my shaker just stopped.  I will try to fix it or may just get the mixer.

Roy

Roy (Capt. Wyoroy FAAGB/USNFAWGB)

John 3:16

  • Member since
    December 2002
  • From: Harrisburg, PA
Posted by Lufbery on Tuesday, January 1, 2008 11:27 AM

Hi all,

Here's just a quick tip when using the paint stirer: make sure it goes all the way to the bottom. I used it recently and splattered myself a little bit when I let the stirer get too close to the top. :(

Regards, 

-Drew

Build what you like; like what you build.

  • Member since
    September 2012
Posted by namrednef on Wednesday, January 2, 2008 5:20 PM

LOL! Anyone who's ever used an electric food mixer has done that too....most likely with mashed potatoes!

Anyway, I purchased the paint mixer on Monday.....based on this thread! From what I read here, I know I'm gonna love it!

 

Nam 

  • Member since
    June 2006
  • From: Calgary
Posted by MaxPower on Wednesday, January 2, 2008 8:53 PM

I have one but I don't use it alot as I found it could make my paint throthy. I'd wrap my pinky finger around the shaft to help contol the speed and keep it straight up and down but it still makes my paint foamy. (Tamiya acrylic)

I also have the Tamiya  paint stirrers and I really like those. At the time I felt silly paying six bucks for 2 stir sticks but I've had them for a couple years now and they look brand new.

  • Member since
    September 2012
Posted by namrednef on Monday, January 7, 2008 8:49 PM

Got my electric paint stirrer today! 7 Days....not bad with a holiday and a weekend in between, but they're just over in Jersey. Very nice catalog from MicroMark also. Only trouble is my 4 in 1 Zona saw came with only 3 of the 4 blades!

....and go figure.....the company that makes the saw is only 15 miles from me!

Oh well, I'll shoot them out a mail and see what they say.

 

Nam 

  • Member since
    December 2002
  • From: Harrisburg, PA
Posted by Lufbery on Monday, January 14, 2008 12:12 PM

Hi all,

Not only is my electric paint stirer good for stiring, it's also great for mixing! I mixed some paint for my Yak-38 model using two parts intermediate blue to one part insignia blue. I stirred both botles first and then mixed into a third bottle. The stirer mixed the two paints and the thinner to a very nice consistency that airbrushed wonderfully.

Regards,

 

-Drew

Build what you like; like what you build.

  • Member since
    January 2006
  • From: Baton Rouge, Snake Central
Posted by PatlaborUnit1 on Monday, January 14, 2008 2:33 PM

I chucked sprue into my dremel and tried that on medium speed. Made a HUGE mess, sloshed foamed paint all over me and the bench and I haven't tried it since.

What was I doing wrong?

David

Build to please yourself, and don't worry about what others think! TI 4019 Jolly Roger Squadron, 501st Legion
  • Member since
    August 2006
  • From: Neenah, WI
Posted by HawkeyeHobbies on Monday, January 14, 2008 3:02 PM

TOO much power Mr Scott! Dremel (corded especially) turn way too fast. The cordless unit I have works fine, just crack open the varible power switch.

Gerald "Hawkeye" Voigt

http://hawkeyes-squawkbox.com/

 

 

"Its not the workbench that makes the model, it is the modeler at the workbench."

  • Member since
    January 2006
  • From: Baton Rouge, Snake Central
Posted by PatlaborUnit1 on Monday, January 14, 2008 6:56 PM

Aye, Cap'n,

We'll ease er' back a bit.....

David  

Build to please yourself, and don't worry about what others think! TI 4019 Jolly Roger Squadron, 501st Legion
JOIN OUR COMMUNITY!

Our community is FREE to join. To participate you must either login or register for an account.

SEARCH FORUMS
FREE NEWSLETTER
By signing up you may also receive reader surveys and occasional special offers. We do not sell, rent or trade our email lists. View our Privacy Policy.