SEARCH FINESCALE.COM

Enter keywords or a search phrase below:

Putting on the I AM STUPID hat tonite!

1460 views
5 replies
1 rating 2 rating 3 rating 4 rating 5 rating
  • Member since
    June 2009
Putting on the I AM STUPID hat tonite!
Posted by jimbot58 on Sunday, April 25, 2010 1:57 AM

I hate it when I do stupid things! I have been working on a Trumpeter 1/144 scale F-22 Raptor, using the instruction sheet of my RoG 1/72 F-22 for a painting guide. Many hours spent masking and painting using combinations of frisket paper, Parafilm "M" and pieces of 3M "Magic" tape. Normally, when I use the 3M tape, I first 'de-tack' it by repeatedly sticking to my fingers until there is very little stickiness left to it.

I finally finished the body of the plane and have been working on the metallics in the exhaust area. I covered the area with the film, trimmed away the sections I wished to paint, and then covered the surrounding areas with the 3M tape and strips of newspaper. I totally forgot to take the stickiness off the tape, and as you can guess...I messed up weeks of work, pulling of bits of the clear finish I had applied and even some paint off the left tail.

I know better and this is not my first day! Why did I forget? DUH!!!!!!

Now I set myself back several days as I repair my goof! I had hoped to start decals tomorrow or the next! Maybe when I leave the house, I should leave a trail with a string so I can find my way home!

Bang HeadOopsPropellerWith Stupid

*******

On my workbench now:

It's all about classic cars now!

Why can't I find the "Any" key on my keyboard?

 

 

 

  • Member since
    June 2006
  • From: Westerville, Ohio
Posted by Air Master Modeler on Sunday, April 25, 2010 10:44 AM

Jim, I would say using "magic" tape was a mistake over any painted surface. Even when you reduce the tackiness it will peel paint with it if left on to long. I found this out the hard way. I switched over to a low tack painters grade masking tape. I reduce the tack further by rubbing the strips against the back of my hands and let the skin oils create a barrier that lets me peel the tape off without peeling off the paint with it. The results have been very good for me.

Also do you paint a primer coat over the model after masking and before you paint it? I have found that painting a primer coat first makes your finishing paint bite down harder to the model surface and makes it very hard for the tape to peel off paint when you remove your masking.

Hope this helps.

Rand

30 years experience building plastic models.

WIP: Revell F-14B Tomcat, backdating to F-14A VF-32 1989 Gulf Of Sidra MiG-23 Killer "Gypsy 207".

  • Member since
    June 2009
Posted by jimbot58 on Sunday, April 25, 2010 12:54 PM

I always mask, paint, and remove the tape all in one session. Tape never stays on more than an hour or two. I learned that lesson long ago, not only on models, but a car I attempted some body work on.

*******

On my workbench now:

It's all about classic cars now!

Why can't I find the "Any" key on my keyboard?

 

 

 

  • Member since
    June 2006
  • From: Westerville, Ohio
Posted by Air Master Modeler on Sunday, April 25, 2010 1:00 PM

That's good but are you laying down a primer coat after masking?  This will really help your primary paint colors adhere hard to the model surface and allow you to peel off the masking without damaging the surrounding paint.

Rand

30 years experience building plastic models.

WIP: Revell F-14B Tomcat, backdating to F-14A VF-32 1989 Gulf Of Sidra MiG-23 Killer "Gypsy 207".

  • Member since
    June 2009
Posted by jimbot58 on Tuesday, April 27, 2010 3:46 AM

I have used MM enamels for years and never used a primer-what would you suggest?

*******

On my workbench now:

It's all about classic cars now!

Why can't I find the "Any" key on my keyboard?

 

 

 

  • Member since
    June 2006
  • From: Westerville, Ohio
Posted by Air Master Modeler on Tuesday, April 27, 2010 12:39 PM

Jim,

I have used several brands of primer paint and the best I have used are Tamiya L flat white primer and Gamesworkshop Skull white primer. Both are excellent spray on primer paints. They spray on very fine and smooth and you do not have to sand between coats. They both come in a spray paint can. The Tamiya brand is also sold in a jar and can be airbrushed. The difference between the two brands are Tamiya is an acrylic primer and Gamesworkshop brand is an enamel yet both can be used with both acrylic and enamel model paints. I have also used Krylon spray primer with good results but you will need to do a little bit of light sanding between coats if you use the Krylon brand. You can find both the Tamiya and Gamesworkshop brands at local hobby shop and they can also be ordered online. I personally prefer the Gamesworkshop brand it costs a few dollars more than the Tamiya brand but you get more for your money.

Rand

30 years experience building plastic models.

WIP: Revell F-14B Tomcat, backdating to F-14A VF-32 1989 Gulf Of Sidra MiG-23 Killer "Gypsy 207".

JOIN OUR COMMUNITY!

Our community is FREE to join. To participate you must either login or register for an account.

SEARCH FORUMS
FREE NEWSLETTER
By signing up you may also receive reader surveys and occasional special offers. We do not sell, rent or trade our email lists. View our Privacy Policy.