SEARCH FINESCALE.COM

Enter keywords or a search phrase below:

Air Man from Mega Man project

1995 views
6 replies
1 rating 2 rating 3 rating 4 rating 5 rating
  • Member since
    October 2004
Posted by gamerabaenre on Monday, April 28, 2008 5:29 PM
Roughly dremeled the aquamend:

More aquamend thrown on top to finalize the sculpt:

Smooth sanding, half way there...


Finished the smooth sanding, and it's time for yet another layer of putty, this time tamiya epoxy quick type:

More smooth sanding...

Yet another putty layer using Mr Surfacer 500... once I lightly sand this smooth, this will be ready for primer, and inevitablly more putty work (probably light curing at that stage...)
  • Member since
    October 2004
Posted by gamerabaenre on Friday, April 25, 2008 11:50 AM
 smeagol the vile wrote:

Hey gam, what exactly are you going to light up with the leds?

His eyes. 

  • Member since
    April 2008
  • From: Philadelphia PA
Posted by smeagol the vile on Friday, April 25, 2008 11:48 AM

Hey gam, what exactly are you going to light up with the leds?

 

  • Member since
    October 2004
Posted by gamerabaenre on Friday, April 25, 2008 11:37 AM
Small update from the past two days of work.  I got the arm pod with battery pack built.



More sanding work on the body.



Aquament epoxy putty work on the body for finer details and filling.



Another test with the LEDs one with a resistor and one without, I'll be going with a resistor along the parallel setup.



Next up is a little mockup of what I have so far.  I used an MG Dom hand in lieu of scratch building my own, saves on time and I think the Dom's fat fingers and hand fit the project decently.  For the arm pod/battery pack, I used some hollowed out PVC pipe capped it with some styrene strips, then placed some barrels in a tri-barrel configuration.  The more I look at the setup, I think I want to cut the barrels down more just to balance things out a bit. I also need to point the LEDs forward as opposed to pointing down.  There are a few other modifications I'll probably make as I look at the mock up more.  But for now...


  • Member since
    October 2004
Posted by gamerabaenre on Wednesday, April 23, 2008 3:26 AM
Got the electronic components together

Adding little connectors to each component, stringing them together with the DPDT switch, I can run the yellow LEDS (Still not completely decided on the color I want the eyes - red, yellow, or blue) from the lithium 3 volt battery and the ducted fan can run off the 1.5 volts coming off the AAA battery cell.


And I even have a little video for it: http://www.gamerabaenre.com/air_man_prog.htm  Scroll to the middle of the page.

Next up, I drilled out the fan hole using a hole saw that was 44mm  in diameter.

Slightly off center, but I'm already working on fixing it :D


And finally, more putty because after drilling the hole, the size of the waist area and area surrounding the hole was too thin, some thin sheet styrene was rolled up and inserted as a cowl for the fan, and doubles as a support for the additional putty slopped onto the kit.  This should be the last putty build up session and next I can work on the final sculpting and surface prep.
  • Member since
    December 2005
  • From: DSM, Iowa
Posted by viper_mp on Tuesday, April 22, 2008 3:13 AM
Interesting idea.  I love the way he did the hand.  I'm just getting back into mechs, so I'll be keeping an eye on this one.

Rob Folden

Secretary / Webmaster- IPMS Plastic Surgeons Member at Large-IPMS Hawkeye Modelers

  • Member since
    October 2004
Air Man from Mega Man project
Posted by gamerabaenre on Monday, April 21, 2008 1:37 PM
New project inspired by the video of another modeler using an MG Z'Gok to scratch build an Air Man from the game Rock Man (Mega Man): http://www.gamerabaenre.com/forums/viewtopic.php?t=166
I gathered the parts on Friday, and during the build gathering, I started work on this.  I have no plans, and I'm just blindly attempting this project using only the video as a reference.  This could go completely south, but so far, I think I'm doing ok....  The complete progress page is here:
My version: http://www.gamerabaenre.com/air_man_prog.htm

And here is the beginnings of this project:



The part that is not explained or shown in the video is the slow process of building up the polyester putty body.  I used strips of styrene as a frame for the putty to grab on to, and once I finish this slow process, I can get to the ever fun sanding and shaping phase...
JOIN OUR COMMUNITY!

Our community is FREE to join. To participate you must either login or register for an account.

SEARCH FORUMS
FREE NEWSLETTER
By signing up you may also receive reader surveys and occasional special offers. We do not sell, rent or trade our email lists. View our Privacy Policy.