LCM-3 Conversion to Navy Dive Boat

Got mine through Masterpiece Models. Being only one state away, they got them here in record time. Surprised the heck out of me. Up to this point I'd been using my architect rule, which works for some scales, but not others very well. For the others, it's break out the calculator and play with the numbers.

I still recall my Mechanical Drawing teacher; "Your scale is not a straight edge! If I catch you using it as such, you will be counting on stubby fingers!" Ah, the good old days, when threats were part of the curriculum.

My scale rulers are 1/87 and 1/160.

Bill

Hi; I bet you got the same rulers I have.

It's out there.Plastruct makes it.

Thanks Dodgy, but it ain't that amazing really. If some company made a kit of your boat, don't you think that you would notice if something was incorrect. Also, I just got some cheater rulers that are specifically for 1/32, 1/35, 1/48, and 1/72 scale. They make conversion work much easier.

Well Brian, it looks pretty good to me. I've just read through the whole thread and am left stunned by how some of you blokes can work such measurements out! Way beyond my math and skills!! Looking great mate.

Parts arrived this morning, inspiring continued work on the boat. Intake and air exhaust vents and port holes went on as well as the roof soft patch. I also did a bit of filler putty work, and when that dries I'll be working on the cabin to pilothouse interface.

Additionally, one of the things we used to do on our dive boat builds was to reinforce the hull bottoms and bottom to side edge. Therefore I added angle iron to that edge and then added a closed towing chock on the bow.

As with scratchbuilds and major kitbash projects, we sometimes get to put everything on hold while awaiting ordered parts and such. With that the case presently, I've contracted with a 'to scale' mini-me to do some touch up work in the interim.

I found him on Angie's List, and haven't checked on his license or references yet. I'm hoping he does decent work, but he's only doing small jobs .  .  . ! 

I'd been holding offstarting the pilot house, mainly because I really wasn't sure how I was going to do it. I had the concept down solid, but undecided on the method; to piece it together, or to build each wall independently and then assemble them as units.

Anyway, after staring at the base for a little while, I just jumped in.

As you may notice, the pilot house portion under construction here is the section above the engine compartment. On the actual boat this part was removable for engine replacement, by unbolting the flange at the base. The forward wall where the helm is located stays with the boat but the front windows go with the pilot house structure.

Started on the foundation for the cox'n flat / pilot house while awaiting mail order parts. Also finished up on the blister, structurally speaking, and started working on the fore deck.

While I was active duty, we always used to prime all bare metal with a light green epoxy. To simulate, I've coated things with a lovely 'satin pistachio'. With the updating of this hull, I also updated the lifting rig instead of using the older style PE parts.

Also, the forward cabin assembly is coming together.

With the fixed bow closure in place, the boat is starting to look more like an LCVP; but give it time, it's coming around. In the mean time, I am continuing with the side and transom blisters. I am also awaiting the delivery of a number of 3D pieces/parts, and have found I need a few more (standby Shapeways, an order is forthcoming!).

Now, that being said, I am somewhat disappointed in the fragility of some of these 1/35 scale 3D products. I ordered some detail items and they are 'to scale', which means really, really, really fragile. "Caveat Emptor" definitely applies here! Now, that particular item was going to be situated below decks so, I guess I'll not make that area visible (though I was hoping to do so) Oh well, such is life. I will assume from now on, that I am just too ham-handed to use such products. (it would have been cool though.)  

As we continue, I've attached the main deck and with the well assembly set in place, I'm starting the side blisters. These will extend the deck out a bit make for better footing when moving around the boat. I have still to chop down the upper well walls.

More progress on the blisters and side walls now abbreviated.

You could think about burnishing aluminum foil over something like a piece of screen or a plastic mesh. Not exactly diamond plate, but it might convey the effect.

I've done something like that to make quilted padding inside a big ugly AN-12.

Bill

Thanks Redleg, I will definately check it out. I had considered the 'flexstone' paints but was worried that they would be too large in effect. The terra cotta should be more sand-like, which is what I'm looking for. I couldn't get any diamond plate for the deck over the fuel tanks, so some texturing is required.

HooYah Deep Sea

I was thinking about a 'treatment' I could put over the open deck sections; the dive deck, the side walkways, cabin top, and bow.

Rustoleum makes textured spray paints.  The Terra Cotta one is perfect for non-slip coating in 1/35.  I use it on armor models all the time.  Just tape off the areas you don't want it and spray away.

More here: https://armorama.kitmaker.net/modules.php?op=modload&name=SquawkBox&file=index&req=viewtopic&topic_id=50656#424251

HooYah Deep Sea

I was thinking about a 'treatment' I could put over the open deck sections

You might want to check over in Armor, as a bunch of modern AFV now include nonskid surfaces, and that's often an add-on for plastic kits.

I know of folk who put down a wet layer of primer and pour microballoons or sanded resin dust over that and lat that set up.

Also, the other armor dodge for texture is Mr Surfacer laid on thick, then stippled with a suitable brush.

Thanks GH, I'll check that out.

I assembled the well and installed the main engine exhaust pipes, then dry fitted the assembly to see where I will need to chop off the upper well walls. I will probably do those cuts after the well assembly is glued in, since the cut will be right at deck level, so before that happens I have to make sure there is nothing left to do inside the hull.

If those areas are in styrene, the common treatment for cast texture, like tank turret, would be to wet the area with Tamiya thin glue, let soften, and stiple with a stiff brush.  Might be a little coarse for your needs though.

Worth a sample run.  Other than that......

I was thinking about a 'treatment' I could put over the open deck sections; the dive deck, the side walkways, cabin top, and bow. The flat deck inside the pilot house will be covered by blue Lonmat.

How about some 400 to 600 grit wet/dry sandpaper, or maybe 320.  Bonus, it's black and ready to weather.

Continuing with the main deck, I changed out the little lazarette hatch for a larger, flush deck one. Trip hazard eliminated on the dive deck and now you can actually get in there (if it were real, but that's the whole idea, right?). Then I put in some support for the forward end of the diving deck. Trying to locate some O scale diamond plate for there.

Forward of that I will start with the framing and support of the pilot house structure.

My next question, since I don't do 1/35 much, is what to use for 'non-skid' grit for this scale?

January 21st.

After a bit more concept work .  .  .  I will have to wait for the kit to decide on how the cox'n flat will get set up. It's a deck height issue; ensuring thatthere is enough overhead for engine maintenance, et al.

Also in this drawing you will note the deck extension. This adds about two feet to the beam and much better footing moving around the dive deck and along the sides. The dive deck will be covered by an awning when we are done.

RC, "You da man!! Thank you so much, that info is awesome. With those dimensions, and since I'm not using the upper well walls or the bow ramp, the trumpeter could actually be built as a 'short 6'. Very cool!

Anyway, this is a basic concept drawing of my intentions. It is based on the boat I ran in Hawaii. I have not decided how much interior detail I'll do as far as the main cabin area goes, but the cox'n flat area should look pretty realistic when done.

HooYah Deep Sea

RC, how much "too deep" do you figure the hull is? I haven't found any drawings that give me the actual dimensions, but it does look deeper than my Program 4 Tango hull, and then should be the same.

If it's close to a foot (hopefully just over), by scale, it could simplify my build considerably.

The difference is 11mm, which is quite a lot. (About 15 scale inches, if my math is right.)     It was easy to find the old review- I just googled "Trumpeter 1/35 LCM-3 review", and it was the first hit.   Here's the link:

https://www.perthmilitarymodelling.com/reviews/vehicles/misc/lcm3/lcm3.htm

I've got 6-boat drawings (remember the 1/12 scale scratchbuild 'Tango'), I can refer to those when the model kit arrives, but until then .  .  . (que up the elevator music).

In the mean time, I'm investigating sources of suitable 1/35 scale components that I will need for this build. Unfortunately, some of the things I was hoping for are not materializing. Most of the boat stuff out there in 1/35 is for WW2 PT boats; I'm needing things slightly more modern, i.e. battle lanterns, flush deck hatches, and ship / boat fittings.

Shapeways has some usable stuff, but going through their 'pages' is time consuming and frustrating due to the excessive duplication.

Okay; I pulled out the drawings and the transom on the LCM-6 Mod 0, which should be the same as the LCM-3, is 4 foot, 3 inches high. Converting that to 1/35 scale equals 1.457 inches. If the Trumpeter hull's transom is taller than 1.457", all good; I can build her as converted from a shortened 6-boat or 50' work boat.

Oh, and TB, the wood boat companies don't really carry those drawings. Despite the multitudinous options of builds that can be done from the LCM-6, nobody carries a wood kit of one. I don't understand why, and I've been pushing Dumas to try it out, but it's a slow process.

HooYah;

    You should be able to get plans for a 6 boat from One of the wood Boat Model companies. other than that, It's up in the air. My real boats were 6s but they were modified for oil spill duties. They had the tapered hulls and only one had the Square Screw Tunnels.The other two were Round Tunnel boats.

Plus the bows had been closed up and cut down to accomodate a foredeck. We also had a welded steel grate walkway over what had been the Well-Deck and Oil Recovery tank.

RC, how much "too deep" do you figure the hull is? I haven't found any drawings that give me the actual dimensions, but it does look deeper than my Program 4 Tango hull, and then should be the same.

If it's close to a foot (hopefully just over), by scale, it could simplify my build considerably.

I built the Trumpeter 1/35 kit when it first came out in 2006 or so. The Trumpeter kit and the Italeri kit appeared at nearly the same time, so I remember reading a lot about both of them. IIRC, the Italeri kit was more costly, but the Trumpeter kit had a hull that was too deep.  I picked the Trumpeter kit because I was converting it to RC, and the bit of extra depth was needed, as it allowed me to fit a NiMh AAcell battery pack amidships under the deck.

Photo is from 2007, with a metal motorized Sherman as cargo. (I later gave up on the idea of trying to animate the ramp. ).   A Sherman is not really an appropriate load for a -3.  I still have the model, and it still runs well.  Its current load is a Dodge 3/4 ton Weapons Carrier, but I am currently building one of the new Tamiya Stuarts to replace it....