Hey Swanny (Toothbrush sander)

both the (i guess this is correct velcro terminology) male and female side of the velcro pads have a self adhesive backing. i just cut small squares of sand paper in a square, stick it on, and trim the excess with scissors. if it wears out eventually, ill just grab another pad and repeat the above. with the opposite piece of velcro, i stick it to the toothbrush and it stays quite handily. ive used them extensively (mostly on hobbycraft and revell models) and have yet to wear one out. i guess you would have to replace it eventually though. the velcro makes it easier and quicker to change out is all. plastic is not too tough on auto sand paper. anyway, let it rip tater chip, if you like what you got, i absolutely love it!!

heck, i like that foam idea as it would probably conform to curves and such a little better than the velcro. i may have to have it your way too. thanks, later.

Chris,

Lets say you take a round piece of 400 grit sandpaper and you glued the velcro to the back of it and after a while it wears out, you will have to glue another piece of velcro to another piece of sandpaper. That was what I meant.

Mike

hey, thats cool mike. what ever works my friend. although ive never had to reglue anything yet. maybe theres a misunderstanding but its not worth explaining if you have your solution at hand. later.

Thanks Chris.

I glued a piece of medium density foam on it and am going to just cut out disks out of sandpaper and spray the backs of them with Super 77 adhesive and stick them to the foam. That velcro idea is good too except you would need to reglue the velcro to each new piece of sandpaper that you use.

Mike

hey mike, heres an idea if its not too late. i bought those little round velcro pads from walmart in the sewing section (about the size of a dime) and glued one side of the pad to the toothbrush and the otherside (which has a peel and stick backing) to the sand paper. i made up several "discs" with varying grits of sandpaper and when i want to swap grits, i just velcro a different pad with a different grit stuck to it. it works well and you dont have to buy a separated head for each grit of sand paper desired.

My father recently purchased a rechargeable sander from Squadron I think.
Just wondering if anyone else ahs used one of these, and if so which has a faster orbital rate?

I bought one of the Braun Oral-B ones at a flea market for $5 a while back.

Mike

You can also glue velcro to the head and then the matching piece different grits of sandpaper. That way, you can change the grit without having to get so many brushes. The padding on the velcro gives the sander a little more give to.

If you got a braun toothbrush, ($20) you can use that and change the heads. The brush head turns faster too.

Could you show some pictures please?

Genius, pure genius!!! I need to do that.

I cut down the bristles as far as I could and then I glued a small piece of wet/dry sandpaper to the brush after the CA glue dried, I was able to trim the paper to a better fit.

Having the extra brush has proven to help in other areas. The brush easily cleans my paint cups. Though I use acrylic paint, sometimes it is a pain to clean. The powered brush makes cleaning easier.

Hello happy toothbrush modifyers
I've found a little variation of use as I cut bristles and stick a little piece of foam ( it comes in rolls and I think it is used to protect water ducts from icing ) on the toothbrush head ( in fact it already has a sticky side ) and then I stick the abrasive piece with double sided adhesive tape.
Just a path to explore...

Medium CA and accelerator.

does it really work, swanny? What do you use to attach the sandpaper, CA glue or PVA?

Swanny,

Thanks

Mike

Crest brush. Cut the bristles off short and glue the sandpaper to that.