SEARCH FINESCALE.COM

Enter keywords or a search phrase below:

Drill bits/pin vise

1179 views
13 replies
1 rating 2 rating 3 rating 4 rating 5 rating
  • Member since
    July 2014
  • From: Franklin Wi
Drill bits/pin vise
Posted by Bakster on Tuesday, July 6, 2021 11:49 AM

Hey folks..  I can use your input. I'd like to get a better set of fine drill bits. Along with that, a good quality pin vise that can accommodate them. I have not had good luck with pin vises. Either the chuck won't close down enough, or open enough, then I have had issues where the drill won't set straight. They are junk. I want some quality. Any thoughts? Does it exist?

  • Member since
    April 2020
Posted by Eaglecash867 on Tuesday, July 6, 2021 12:14 PM

This one is the last pin vise you'll ever need to buy.  Amazing quality, and its seemingly-unwieldy size and weight are actually very beneficial to control and precision.

https://www.amazon.com/Tamiya-Fine-Vise-0-1-3-2mm-74112/dp/B00EEOD03C/ref=pd_lpo_21_t_0/143-2198274-0825321?_encoding=UTF8&pd_rd_i=B00EEOD03C&pd_rd_r=a10c435a-2589-425c-a060-396023543d1d&pd_rd_w=4JtEG&pd_rd_wg=I7MJ7&pf_rd_p=fb1e266d-b690-4b4f-b71c-bd35e5395976&pf_rd_r=6CEH01475AHRQ4GEJV1C&psc=1&refRID=6CEH01475AHRQ4GEJV1C

Recently bought a set of these and have been using them happily for drilling tiny holes in styrene.  Not sure if they fit in a pin vise though.  I usually just use my index finger as the pivot point for the back of the bit and slowly spin them with my adjacent finger and thumb.  They were indispensable for drilling the tiny holes I needed for the styrene "cables" on my scratchbuilt F-16 JHMCS MTU.

https://www.amazon.com/gp/product/B07C5S3FM2/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

"You can have my illegal fireworks when you pry them from my cold, dead fingers...which are...over there somewhere."

  • Member since
    July 2014
  • From: Franklin Wi
Posted by Bakster on Tuesday, July 6, 2021 2:50 PM

Eaglecash867

This one is the last pin vise you'll ever need to buy.  Amazing quality, and its seemingly-unwieldy size and weight are actually very beneficial to control and precision.

https://www.amazon.com/Tamiya-Fine-Vise-0-1-3-2mm-74112/dp/B00EEOD03C/ref=pd_lpo_21_t_0/143-2198274-0825321?_encoding=UTF8&pd_rd_i=B00EEOD03C&pd_rd_r=a10c435a-2589-425c-a060-396023543d1d&pd_rd_w=4JtEG&pd_rd_wg=I7MJ7&pf_rd_p=fb1e266d-b690-4b4f-b71c-bd35e5395976&pf_rd_r=6CEH01475AHRQ4GEJV1C&psc=1&refRID=6CEH01475AHRQ4GEJV1C

Recently bought a set of these and have been using them happily for drilling tiny holes in styrene.  Not sure if they fit in a pin vise though.  I usually just use my index finger as the pivot point for the back of the bit and slowly spin them with my adjacent finger and thumb.  They were indispensable for drilling the tiny holes I needed for the styrene "cables" on my scratchbuilt F-16 JHMCS MTU.

https://www.amazon.com/gp/product/B07C5S3FM2/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

 

Oh man, those look good. Being Tamiya, the vise must be good. And those drill bits look really good. Maybe if I get those bits I won't need a pin vise, just do what you do.

Thanks for the links. I will look into it more!

  • Member since
    April 2020
Posted by Eaglecash867 on Tuesday, July 6, 2021 2:59 PM

Bakster
Oh man, those look good. Being Tamiya, the vise must be good. And those drill bits look really good. Maybe if I get those bits I won't need a pin vise, just do what you do. Thanks for the links. I will look into it more!

No problem, Bakster.  I had the same issues you have had with other pin vises, and the Tamiya made all of that go away.

"You can have my illegal fireworks when you pry them from my cold, dead fingers...which are...over there somewhere."

  • Member since
    July 2014
  • From: Franklin Wi
Posted by Bakster on Tuesday, July 6, 2021 3:10 PM

Eaglecash867

 

 
Bakster
Oh man, those look good. Being Tamiya, the vise must be good. And those drill bits look really good. Maybe if I get those bits I won't need a pin vise, just do what you do. Thanks for the links. I will look into it more!

 

No problem, Bakster.  I had the same issues you have had with other pin vises, and the Tamiya made all of that go away.

 

Yes

  • Member since
    September 2012
Posted by GMorrison on Tuesday, July 6, 2021 4:30 PM

Eagle, your tool suggestions are really helpful to me.

 

Bill

 Modeling is an excuse to buy books.

 

  • Member since
    April 2020
Posted by Eaglecash867 on Tuesday, July 6, 2021 6:39 PM

GMorrison

Eagle, your tool suggestions are really helpful to me.

Bill

 
Bill, glad to help when I can.  Good quality tools and supplies are sometimes really hard to come by, so when I find good ones, I like to share and maybe spare others the frustration of getting bad tools.

"You can have my illegal fireworks when you pry them from my cold, dead fingers...which are...over there somewhere."

  • Member since
    May 2013
  • From: Indiana, USA
Posted by Greg on Tuesday, July 6, 2021 7:33 PM

Strongly agree with Eagle. I haven't broken a bit since I used my first Tamiya pin vise, have since bought 2 more.

They have some interesting varieties, check them all out. I have 3, all different models.

That said, I'd recommend the one Eagle linked to, the 74112. It has two double ended chucks which is how it handles the wide diameter range of .1 - 3.2mm. Also, it is a really well-designed and machined tool. Had I bought this one first, I'm not sure I'd need the other two.

-Greg

  • Member since
    August 2014
  • From: Willamette Valley, Oregon
Posted by goldhammer on Tuesday, July 6, 2021 9:35 PM

I like quality stuff too, guess it comes from a lifetime of wrenching on fullsize stuff.

That being said, just watched a few bucks fly off like the last swallow that left the bird house yesterday.

  • Member since
    June 2021
Posted by rocketman2000 on Wednesday, July 7, 2021 7:34 AM

I have found some really nice pin vises, but I still break the smaller bits.  It may be due to my worsening manual dexterity.  I decided to try a more expensive set from a well known American machine tool company.  I'm breaking bits at the same rate.  I've come to regard as a supply item just like glue, paint, and paper towels!

 

Don Stauffer in Minnesota

  • Member since
    July 2014
  • From: Franklin Wi
Posted by Bakster on Wednesday, July 7, 2021 7:35 AM

goldhammer

I like quality stuff too, guess it comes from a lifetime of wrenching on fullsize stuff.

That being said, just watched a few bucks fly off like the last swallow that left the bird house yesterday.

 

Yeah sometimes quality counts. I have 4 pin vises and none of them are worth keeping. I easily spent double the price of a new Tamiya version

 

  • Member since
    July 2014
  • From: Franklin Wi
Posted by Bakster on Wednesday, July 7, 2021 7:37 AM

Greg

Strongly agree with Eagle. I haven't broken a bit since I used my first Tamiya pin vise, have since bought 2 more.

They have some interesting varieties, check them all out. I have 3, all different models.

That said, I'd recommend the one Eagle linked to, the 74112. It has two double ended chucks which is how it handles the wide diameter range of .1 - 3.2mm. Also, it is a really well-designed and machined tool. Had I bought this one first, I'm not sure I'd need the other two.

 

Hey Greg, thanks for the input. You guys have me sold. I will try them. Surprise

  • Member since
    April 2020
Posted by Eaglecash867 on Wednesday, July 7, 2021 8:55 AM

goldhammer
I like quality stuff too, guess it comes from a lifetime of wrenching on fullsize stuff.

Yup.  That's where mine comes from too.  Over the last 3 decades, I have found that the "cheap" tools actually cost you more in a very short amount of time due to lost productivity and schedule over-runs.  Time is money too.  A lot of people forget that.

At work, I'm sometimes referred to as The Wiha Man, due to my preference for Willi Hahn tools.  Can't really say that I'm a loyal, repeat customer though.  Any purchase I have made from them has lasted at least 20 years with heavy use, so I don't have to buy from them very often.

"You can have my illegal fireworks when you pry them from my cold, dead fingers...which are...over there somewhere."

  • Member since
    October 2019
  • From: New Braunfels, Texas
Posted by Tanker-Builder on Wednesday, July 7, 2021 11:40 AM

Hi;

 I have a Tamiya Pin Vise that's all the way back from they first offered one with the Swivel Wood ball on top. I got Three Chucks and a whole Box of bits with it. Ya know what? I still got a whole box of bits. Over the years probably broke at least five. My Bad, Not the product. I got in a hurry. That's a No-No!

JOIN OUR COMMUNITY!

Our community is FREE to join. To participate you must either login or register for an account.

SEARCH FORUMS
FREE NEWSLETTER
By signing up you may also receive reader surveys and occasional special offers. We do not sell, rent or trade our email lists. View our Privacy Policy.