Greetings. New and after advice on glue :)

Tanker-Builder

Do what I did and fix it with the super type glue that cures with uv lite...

 

Just wondering what UV Curing Adhesive you might recommend for gluing the key? 

I came across this glue,... 

http://www.chemtools.com.au/product/adhesives-sealants/instant-adhesives/rapidstick-8414-cyanoacrylate-adhesive/

...and though it's a "Cyanoacrylate Adhesive", this website has a table which says UV curable adhesives have good resistance...

https://www.antala.uk/adhesive-for-bonding-abs/


I sent an email off to Corsair to confirm the keys on the K55 are ABS to, just in case.

[edit] Corsair got back to me and said they were ABS keys.

Thanks,

gregbale

That's always potentially an issue with small parts. If you have the space, then any kind of reinforcement might help.

It occurs to me to ask...have you looked into simply getting a replacement key? They are available for most models, and there are quite a few Youtube videos demonstrating the necessary procedures. It might be cheaper in the long run than trying to repair it.

Thanks for the reply :). I've contacted Corsair, just waiting on a reply. From what I've found online however, because the keyboard is a membrane style keyboard, it's unlikely I'll be able to get replacement keys, unlike Mechanical keyboards, where keys are easier to replace.

Widget

The one thing that concerns me is whether the surface area of the key that's to be glued is going to be too small, and therfor lack strength? If I were to reinforce, how would I go about that? just glue strips of ABS on the underside of the key ?

That's always potentially an issue with small parts. If you have the space, then any kind of reinforcement might help.

It occurs to me to ask...have you looked into simply getting a replacement key? They are available for most models, and there are quite a few Youtube videos demonstrating the necessary procedures. It might be cheaper in the long run than trying to repair it.

Thanks for the welcome and suggestions :)

A quick google I believe the key is made of ABS plastic, so the cement kind might be best. I've only used Acetone in the past to fix a ABS car door handle, but I had much more to work with.
The one thing that concerns me is whether the surface area of the key that's to be glued is going to be too small, and therfor lack strength? If I were to reinforce, how would I go about that? just glue strips of ABS on the underside of the key ?

Tanker-Builder

Do what I did and fix it with the super type glue that cures with uv lite 

Thanks for the suggestion :). How does the UV glue compare to Superglue or ABD cement? I have a UV light here that I got off ebay, though don't know if these cheap lights are true UV lights or just purple.


On the topic of models, one thing I'm curious of it, what do you guys do with your models once done? Do you sell then invest in more models?
I ask as, even though model making seems fun, the cost of each model seems costly, and they would eventually take up space.


Thanks again for the feedback and welcomes :)

Welcome to the forums!

As to your key...it's most likely ABS plastic, the same material used in some types of plastic plumbing fittings (and Lego blocks!). Small cans of solvent-type ABS cement should be available at most home centers and hardware stores.

Good luck with your repair.

the Baron

 

 

Tojo72

Welcome to the forums,if you ever start up building models we will be here to help you along  

 

 

 

 

I've had good luck with LePage's 100% glue. I've used it to glue metal to glass, wood to wood, and various types of plastic (not styrene), and to repair a tear in the woft soft rubber handle of a paring knife. This is what the product looks like; it's available in almost any hardware store:

Good luck with your keyboard.

Bob

 

Tojo72

Welcome to the forums,if you ever start up building models we will be here to help you along  

Hi;

 Welcome to the forums. As to your broken key. Do what I did and fix it with the super type glue that cures with uv lite or just use two part epoxy.  Although I have worked with plastics I can say the key definitely NOT Styrene!

Welcome to the forums,if you ever start up building models we will be here to help you along 

Or maybe superglue with some accelerator like zip kicker.  Really depends on the material.  Good suggestions above.

Welcome to the Forum!

I think it depends on the type of plastic.  Styrene would probably react very well to a combination of traditional tube glue, with some liquid cement added.  I've found that will hold very well, because it "melts" the plastic together.

Other types of plastic don't react real well.

Maybe some kind of epoxy?