SEARCH FINESCALE.COM

Enter keywords or a search phrase below:

Simulating 'FUR"

848 views
6 replies
1 rating 2 rating 3 rating 4 rating 5 rating
  • Member since
    November 2005
  • From: Somewhere over the rainbow
Posted by m1garand on Thursday, April 27, 2006 5:35 PM
 goldenturtle02 wrote:

All the above ideas sound good. I have decent results with flocking from Detail Master.  But you should practice on something that you can do without, an old car body? Mayhaps a Cougar, or a Jaguar or maybe a Mustang and lastly a Sunbeam Tiger. Hmmmm I may build a furry Jag.......

Don't forget to add purple velvet seats with zebra stripes with it. I forgot that  this is the plastic modeling forum, not a Pimp MAH Ride forum. j/k Big Smile [:D] 

Best regards,

Huggy Bear

  • Member since
    May 2004
  • From: Aberdeen, Scotland
Posted by Colin Russell on Sunday, April 16, 2006 2:52 PM

If the kit is plastic, then you can brush-paint a little area with liquid poly cement to soften the plastic's surface.  Then use a needle in a small pin vice and quickly scribe 'fur' lines into the plastic.  Keep going till you cover the model.  When finished, take an old bit of Scotchbrite over it to remove any stringy bits of plastic and there you are ....fur!

The same technique can be used on plastic figures for dioramas to improve the quality of the hair on a human head.  Hope this helps.

  • Member since
    November 2003
  • From: Western Maryland
Posted by goldenturtle02 on Wednesday, April 12, 2006 1:27 PM

All the above ideas sound good. I have decent results with flocking from Detail Master.  But you should practice on something that you can do without, an old car body? Mayhaps a Cougar, or a Jaguar or maybe a Mustang and lastly a Sunbeam Tiger. Hmmmm I may build a furry Jag.......

Man these blades are sharp....... Where's this red stuff coming from????
  • Member since
    April 2003
  • From: Sunny Florida
Posted by renarts on Monday, April 3, 2006 9:40 PM
If you are going to use putty over the existing surface, a piece of fine wire with a loop in it makes a nice fur texturing tool. The other thing that works pretty well is taking a small swatch of craft fur and laying it down and pressing it into the putty. When you lift it off.....fur.
Mike "Imagination is the dye that colors our lives" Marcus Aurellius A good friend will come and bail you out of jail...but, a true friend will be sitting next to you saying, "Damn...that was fun!"
  • Member since
    November 2005
Posted by Anonymous on Monday, April 3, 2006 9:19 PM
Epoxy is my vote. Let it set for about 30 minutes, and then use an exacto blade, with short, quick, shallow cuts, all in one general direction. As the putty sets, you can texture it finer and finer. I'd take a toothpick ot the end of a brush, and block out the sections of the fur first, and then start laying in the texture.
  • Member since
    March 2003
  • From: Jacksonville, NC
Posted by Wolfp on Monday, April 3, 2006 6:22 PM
Is it plastic.  If so you might consider using a hot iron to scribe the fur.  Also, epoxy putty could probably be used and sculpted into a fur texture.  Just some ideas.

J.B. http://photobucket.com/albums/a303/jbrunyon/

    

On the Bench: !/350 TOS Enterprise; 1/72 Tie Interceptor

  • Member since
    November 2005
Simulating 'FUR"
Posted by Anonymous on Monday, April 3, 2006 6:10 PM
anyone with experience simulating fur on an animal figure?  Does that flocking material from craft stores do a decent job?  I'm doing a vintage Aurora Cave Bear and think it'd look good with some texture.  Thanks friends.
JOIN OUR COMMUNITY!

Our community is FREE to join. To participate you must either login or register for an account.

SEARCH FORUMS
FREE NEWSLETTER
By signing up you may also receive reader surveys and occasional special offers. We do not sell, rent or trade our email lists. View our Privacy Policy.