SEARCH FINESCALE.COM

Enter keywords or a search phrase below:

Moebius Voyager *PICS*

6526 views
12 replies
1 rating 2 rating 3 rating 4 rating 5 rating
Moderator
  • Member since
    April 2006
  • From: my keyboard dreaming of being at the workbench
Posted by Aaron Skinner on Friday, June 12, 2009 1:00 PM
Cheers!Make a Toast [#toast]

Aaron Skinner

Editor

FineScale Modeler

  • Member since
    April 2008
  • From: Philadelphia PA
Posted by smeagol the vile on Friday, June 12, 2009 11:51 AM
well it looks like a beast of a kit and you did a nice job on it.

 

Moderator
  • Member since
    April 2006
  • From: my keyboard dreaming of being at the workbench
Posted by Aaron Skinner on Friday, June 12, 2009 11:44 AM
 smeagol the vile wrote:

 On the vent behind the cockpit, the inner edge looks like it could use some find sanding to get it smooth and not jagged

Yeah, that was one of the worst areas. The edge of the vents was pretty thin, with an undercut behind, so it was easily damaged while I sanded out the floor of the intake that needed a lot of filler to blend completely.

Aaron Skinner

Editor

FineScale Modeler

  • Member since
    April 2008
  • From: Philadelphia PA
Posted by smeagol the vile on Friday, June 12, 2009 11:21 AM

Very nice, I like the detail in the cockpit.  The only thing I can say for improvement would be best shown in this pic

 On the vent behind the cockpit, the inner edge looks like it could use some find sanding to get it smooth and not jagged

 

  • Member since
    May 2009
Posted by trekriffic on Friday, June 12, 2009 10:14 AM

Beautiful  job ! That finish is perfect !

I have the same kit. I hope mine comes out half as good as yours !

Patsy: "It's only a model."
Moderator
  • Member since
    April 2006
  • From: my keyboard dreaming of being at the workbench
Posted by Aaron Skinner on Monday, May 12, 2008 6:18 PM

 DaveP wrote:
I built one without paint for a short review article. This makes me want to do another "for real," maybe with lights and fiber optics.

Thanks. Yeah, lights, etc., would be great. You could probably see the fourth crew member back in the depths of the cabin with a couple of grain of wheat ot LEDs inside. What's nice about this one is you can pretty much have at it creatively. How about some aztec paneling to break up the surface, scratchbuilt  landing gear, etc?

 

Aaron Skinner

Editor

FineScale Modeler

  • Member since
    February 2008
Posted by DaveP on Monday, May 12, 2008 5:07 PM
That looks great. I built one without paint for a short review article. This makes me want to do another "for real," maybe with lights and fiber optics.
Moderator
  • Member since
    April 2006
  • From: my keyboard dreaming of being at the workbench
Posted by Aaron Skinner on Monday, May 12, 2008 1:17 PM
 Cosmic J wrote:

Hey, check that out. That's much nicer than I anticipated. The cockpit and turret moldings have some pretty good detail in there.

Yeah, it's not too bad especially for a kit from a cartoon show. All-in-all a very enjoyable build. Next up I might tackle the Polar Lights Spindrift. 

Aaron Skinner

Editor

FineScale Modeler

  • Member since
    December 2007
  • From: Louisville, KY.
Posted by Cosmic J on Monday, May 12, 2008 12:29 PM

Hey, check that out. That's much nicer than I anticipated. The cockpit and turret moldings have some pretty good detail in there. Good paint job too.

Thanks - JC

Moderator
  • Member since
    April 2006
  • From: my keyboard dreaming of being at the workbench
Posted by Aaron Skinner on Monday, May 12, 2008 10:09 AM

Cosmic J and Griff,

Thanks for the comments. There is a certain amount of filler involved, but the ships clean lines make it easy to avoid messing up engraved panel lines, etc.

Here's a close-up of the cockpit:

Cheers, 

Aaron Skinner

Editor

FineScale Modeler

  • Member since
    June 2004
  • From: The House of Blues Clues
Posted by Griffworks on Saturday, May 10, 2008 7:35 AM

Very nice!  I've never seen an episode of the cartoon, tho have watched the movie many times.  Echoing what Cosmic J said, I think you nailed it w/regards to getting a nice, clean set of lines. 

Excellent work, Aaron. Thumbs Up [tup]

The greatest measure of a man is his children and what kind of people they are.

 

  • Member since
    December 2007
  • From: Louisville, KY.
Posted by Cosmic J on Friday, May 9, 2008 6:42 PM

Man, I bet that was a bear to sand and fill. That's the thing about gloss white finishes, no way to hide the mistakes, you just gotta clean 'em up. Looks like you nailed it tho'.

Have any closeups of the cockpit?

Moderator
  • Member since
    April 2006
  • From: my keyboard dreaming of being at the workbench
Moebius Voyager *PICS*
Posted by Aaron Skinner on Friday, May 9, 2008 3:39 PM

Here's Moebius' repop of Aurora's Voyager from the cartoon Fantastic Voyage. It was a fun and challenging build. There aren't many parts but the fit needs refinement in several places. Nothing putty and super glue can't fix. And I love gloss white paint scheme; so easy to apply.

Enjoy. Comments and criticisms always appreciated.

Cheers, 

Aaron Skinner

Editor

FineScale Modeler

JOIN OUR COMMUNITY!

Our community is FREE to join. To participate you must either login or register for an account.

SEARCH FORUMS
FREE NEWSLETTER
By signing up you may also receive reader surveys and occasional special offers. We do not sell, rent or trade our email lists. View our Privacy Policy.