SEARCH FINESCALE.COM

Enter keywords or a search phrase below:

Another Omni 4000 Question

586 views
6 replies
1 rating 2 rating 3 rating 4 rating 5 rating
  • Member since
    April 2003
  • From: Hayward, CA
Posted by MikeV on Thursday, October 7, 2004 7:27 PM
It is also possible to get a paint clump stuck in there so that it does that while painting. In that case you just pull the needle back, blast some paint through it and push the needle back into the tip.
This usually clears the problem.

Mike

Wisdom is the right use of knowledge. To know is not to be wise. Many men know a great deal, and are all the greater fools for it. There is no fool so great a fool as a knowing fool. But to know how to use knowledge is to have wisdom. " Charles Spurgeon
  • Member since
    January 2004
  • From: USA
Posted by MusicCity on Thursday, October 7, 2004 6:23 PM
I do the same thing from time to time when I clean mine. I'd have sworn the needle was seated but next time I use it I start to get paint as soon as I give it air. After the first time you know what causes it, reseat the needle, and keep on going.
Scott Craig -- Nashville, TN -- My Website -- My Models Page
  • Member since
    March 2004
  • From: British Columbia,Canada
Posted by bstrump on Thursday, October 7, 2004 3:43 PM
Thanks for your reply, Jeff. I'll remeber that tip for the future. MikeV was bang on with his suggestion though. When I first looked at it, I would' ve sworn up and down that the needle was completely seated, because when I followed Mike's advice, the needle really didn't move at all. Now that I have this glitch taken care of, I'm absolutely amazed at what I can now do. Swiching from the Badger 200 was almost like stepping into another universe.
Cheers
  • Member since
    November 2005
Posted by Anonymous on Thursday, October 7, 2004 11:09 AM
Another thing too. What could be happening is you are shuting the paint off during your practice before shutting the air off, which leaves a small bit of paint on the needle which blows out in a small blob when you start to paint the next stroke. its all trigger practice.
Jeff
  • Member since
    March 2004
  • From: British Columbia,Canada
Posted by bstrump on Tuesday, October 5, 2004 11:00 PM
Thanks for your reply, Mike. I had a suspicion that's what it might be but I didn't want to start messing with it until I heard from someone more knowledgable than myself. When I get home tonight I'll try your suggestion. Once again, thank you.

Bert
  • Member since
    April 2003
  • From: Hayward, CA
Posted by MikeV on Tuesday, October 5, 2004 10:39 PM
Is the needle seated into the tip properly?
Take off the handle, loosen the needle chuck, and push the needle forward until it makes firm contact with the tip and re-tighten the needle chuck.
Don't push too hard on the needle though as you don't want to damage the tip.

Mike

Wisdom is the right use of knowledge. To know is not to be wise. Many men know a great deal, and are all the greater fools for it. There is no fool so great a fool as a knowing fool. But to know how to use knowledge is to have wisdom. " Charles Spurgeon
  • Member since
    March 2004
  • From: British Columbia,Canada
Another Omni 4000 Question
Posted by bstrump on Tuesday, October 5, 2004 10:31 PM
I just got mine yesterday and today I played with it a bit. I noticed however that when I depress the trigger, it's flowing paint even before I've rocked the trigger back. This can't be right. Anybody got an idea of what's going on and how I can fix it? It's spraying about a1/32 to 1/16 pattern just by pressing the trigger down.

Other than this little glitch, it's performing light years ahead of my Badger 200. I can see though that I'll have to break down and get a regulator as well.
JOIN OUR COMMUNITY!

Our community is FREE to join. To participate you must either login or register for an account.

SEARCH FORUMS
FREE NEWSLETTER
By signing up you may also receive reader surveys and occasional special offers. We do not sell, rent or trade our email lists. View our Privacy Policy.