SEARCH FINESCALE.COM

Enter keywords or a search phrase below:

Dull vs bright

965 views
7 replies
1 rating 2 rating 3 rating 4 rating 5 rating
  • Member since
    March 2003
  • From: Chipley FL
Posted by urich on Tuesday, May 16, 2006 10:40 AM
I do the standard soap and water wash and let dry the paint i use in Model Master And I use the Blue masking tape or low tact scotch tape But I think I will try some of the Alcad paint when I get back to the states
  • Member since
    April 2003
  • From: Hayward, CA
Posted by MikeV on Friday, May 12, 2006 8:33 PM
 urich wrote:

Mike how do you go about masking the color to spray the say the silver color.  In other works when I paint silver then mask even with a low tac tape I end up pelling off some of the paint? When I'm home I have to work fast to complete just a few of the kits before I leave again. so time is not on my side. J




What paint are you using and how are you preparing the surface?


Wisdom is the right use of knowledge. To know is not to be wise. Many men know a great deal, and are all the greater fools for it. There is no fool so great a fool as a knowing fool. But to know how to use knowledge is to have wisdom. " Charles Spurgeon
  • Member since
    February 2006
Posted by Neptune48 on Friday, May 12, 2006 10:53 AM
 urich wrote:

Mike how do you go about masking the color to spray the say the silver color.  In other works when I paint silver then mask even with a low tac tape I end up pelling off some of the paint? When I'm home I have to work fast to complete just a few of the kits before I leave again. so time is not on my side. J

I'd recommend switching to Alclad 2.  They have seven variants on aluminum* and the paint does not lift when masked.  A single bottle looks pricey, but it goes a long way and yields superior results.  BYW, I'm not affiliated in any way with the company, just a fan who has done a little research.

http://www.alclad2.com/alclad-home.html

*Alclad 2 Aluminum paints:
Polished Aluminum      Dark Aluminum      Duraluminum      Aluminum
White Aluminum          Dull Aluminum        Airframe Aluminum

          

"You can't have everything--where would you put it?"
  • Member since
    March 2003
  • From: Chipley FL
Posted by urich on Friday, May 12, 2006 9:19 AM

Mike how do you go about masking the color to spray the say the silver color.  In other works when I paint silver then mask even with a low tac tape I end up pelling off some of the paint? When I'm home I have to work fast to complete just a few of the kits before I leave again. so time is not on my side. J

  • Member since
    August 2005
  • From: Sydney, Australia
Posted by Phil_H on Friday, May 12, 2006 8:52 AM
 H2O_MARK wrote:

That would be my suggestion too as I've never seen a "flat-aluminum" at least not readily available in a bottle.

Of course with as long as I've been away from the bench they probably have one out now.

Actually, Tamiya make a Flat Aluminum - XF-16.  However, if the difference between "bright" and "flat" is quite subtle, I'd go with the "clear flat" over the "dull" areas too.

  • Member since
    November 2005
Posted by Anonymous on Friday, May 12, 2006 8:44 AM

 MikeV wrote:
You could spray clear flat on the "dull aluminum" parts and leave the "bright aluminum" glossy.

That would be my suggestion too as I've never seen a "flat-aluminum" at least not readily available in a bottle.

Of course with as long as I've been away from the bench they probably have one out now.

  • Member since
    April 2003
  • From: Hayward, CA
Posted by MikeV on Friday, May 12, 2006 7:59 AM
You could spray clear flat on the "dull aluminum" parts and leave the "bright aluminum" glossy.

Wisdom is the right use of knowledge. To know is not to be wise. Many men know a great deal, and are all the greater fools for it. There is no fool so great a fool as a knowing fool. But to know how to use knowledge is to have wisdom. " Charles Spurgeon
  • Member since
    March 2003
  • From: Chipley FL
Dull vs bright
Posted by urich on Thursday, May 11, 2006 10:29 PM
I have a couple of modles that call for places to be bright aluminum and other places to be dull aluminin how do you do this? thanks J Urich
JOIN OUR COMMUNITY!

Our community is FREE to join. To participate you must either login or register for an account.

SEARCH FORUMS
FREE NEWSLETTER
By signing up you may also receive reader surveys and occasional special offers. We do not sell, rent or trade our email lists. View our Privacy Policy.